Page 233 - Full GAP Catalogue 2022
P. 233
Barriers & Fencing (Non-Mechanical) / 231
Security Fencing FE001
These anti-climb fence panels are fabricated from pre-
galvanised steel and reinforced with power web corners.
Common for construction sites and events.
• Available in square or round top versions
• Accessories available, see next page
• Easy to transport, install and dismantle
• Two weeks minimum hire
Code FE001
Description Anti-Climb Fence Panel
Length 3.45m SALE
Height 2.0m ITEM
Weight 13.4kg
1015
ALL DIMENSIONS IN MILLIMETRES THIRD ANGLE PROJECTION
REMOVE ALL SHARP EDGES DO NOT SCALE DRAWING
Square Top Fence Panel Specification Round Top Fence Panel Specifications 1020
ALL DIMENSIONS IN MILLIMETRES THIRD ANGLE PROJECTION
DO NOT SCALE DRAWING
REMOVE ALL SHARP EDGES
"
"
" !
% ' ! - -
! - 0 - ' " !
! " " "
! " TITLE:
TOLERANCES - UNLESS STATED OTHERWISE ! ' ! % - - 0 ' - - " !
*
* % ! & ! , & " * * ! TOLERANCES - UNLESS STATED OTHERWISE TITLE:
! " " " UNTOLERANCED DIMENSIONS +/- 2mm " " " ! UNTOLERANCED DIMENSIONS +/- 2mm
+/- 2mm
CUTTING LENGTHS
* * * * , % ! & ! " & ! Installation of Fence Panels CUTTING LENGTHS +/- 2mm
UP TO 300mm
+/- 1mm
" " " ! +/- 2mm NAME SIGNATURE DATE MATERIAL: UP TO 300mm +/- 1mm NAME SIGNATURE DATE MATERIAL:
1001mm & ABOVE
FABRICATION UP TO 1000mm +/- 3mm DRAWN G. CRICK 2/11/7 . CARBON STEEL FABRICATION UP TO 1000mm +/- 2mm DRAWN G. CRICK 28/2/11 . CARBON STEEL
+/- 3mm
1001mm & ABOVE
ANGULAR
+/- 1
CHK'D
ANGULAR
+/- 1
CHK'D
For any site security fencing hire, FINISH: PRE-GALVANISED Drw / Stockcode No. Revision MACHINING +/- 0.2mm FINISH: PRE-GALVANISED Drw / Stockcode No. Revision
PROPERTIES & TOLERANCES)you will more than likely need to erect and dismantle the fencing yourself, so GAP has compiled
MACHINING
+/- 0.2mm
GAUGE
+/- 10%
GAUGE
+/- 10%
THE COMPANY RETAIN THE RIGHT TO PERIODICALLY ALTER INFORMATION WITHIN THIS DRAWING SHEET AND WILL ATTE MPT TO NOTIFY ALL PARTIES WEIGHT +/- 10% (DUE TO MATERIAL NONE +/- 10% (DUE TO MATERIAL NONE
THE COMPANY RETAIN THE RIGHT TO PERIODICALLY ALTER INFORMATION WITHIN THIS DRAWING SHEET AND WILL ATTE MPT TO NOTIFY ALL PARTIES
CONCERNED OF ANY CHANGES AND THE INFORMATION ON THI S SHEET SHOULD NOT BE REPRODUCED WITHOUT THIER WRITTEN CONSENT. CONCERNED OF ANY CHANGES AND THE INFORMATION ON THI S SHEET SHOULD NOT BE REPRODUCED WITHOUT THIER WRITTEN CONSENT. WEIGHT PROPERTIES & TOLERANCES)
a quick and easy step-by-step guide to help you get the job done. ,
WEIGHT: ) SCALE: 1:12.5 SHEET 1 OF 2 WEIGHT: SCALE: 1:12.5 SHEET 1 OF 3
STEP 1: Position fencing bases along the proposed fence line using a spacing gauge (a piece of timber cut to size will suffice). The
panels are supported by inserting the side posts into the holes cast in the centre of the base. Each base is cast with at least four
post support positions for flexibility of use with hand hold positions in each end of the base.
STEP 2: The fence panels can then be carefully placed into position. This is best done by more than one person.
STEP 3: With all the panels in position, security clamps should then be placed approximately 650mm from the top of the panel,
across the adjoining side posts. A 20mm box type spanner is required to secure the clamp with the central nut and bolt.
